[Pacemaker] cluster heartbeat is not used
Dvorak Andreas
Andreas.Dvorak at baaderbank.de
Mon Dec 9 15:27:25 UTC 2013
Hi,
thank you for the quick answers.
I thought I would need to edit the corosync.conf file. So I do not need to?
Where should I configure the heartbeat interconnect interfaces?
With corosync-cfgtool -s it shows the wrong ip? But where does that come from?
Andreas
Von: emmanuel segura [mailto:emi2fast at gmail.com]
Gesendet: Montag, 9. Dezember 2013 16:05
An: The Pacemaker cluster resource manager
Betreff: Re: [Pacemaker] cluster heartbeat is not used
because in your corosync-cfgtool -s you are using bonding address
2013/12/9 Dvorak Andreas <Andreas.Dvorak at baaderbank.de<mailto:Andreas.Dvorak at baaderbank.de>>
Hi
Here it is
cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: em3
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: em3
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: c8:1f:66:d7:3b:fe
Slave queue ID: 0
Slave Interface: p3p3
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 00:0a:f7:3e:ca:8e
Slave queue ID: 0
Andreas
Von: emmanuel segura [mailto:emi2fast at gmail.com<mailto:emi2fast at gmail.com>]
Gesendet: Montag, 9. Dezember 2013 15:50
An: The Pacemaker cluster resource manager
Betreff: Re: [Pacemaker] cluster heartbeat is not used
show cat /proc/net/bonding/bond0
2013/12/9 Dvorak Andreas <Andreas.Dvorak at baaderbank.de<mailto:Andreas.Dvorak at baaderbank.de>>
Dear all,
during failover tests I found out that I can put down the heartbeat interfaces and the cluster ignores that. But if I put down bond0 the fencing is running.
Can please somebody help me?
bond0 Link encap:Ethernet HWaddr C8:1F:66:D7:3B:FE
inet addr:10.15.28.36 Bcast:10.15.255.255 Mask:255.255.0.0
inet6 addr: fe80::ca1f:66ff:fed7:3bfe/64 Scope:Link
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
em4 Link encap:Ethernet HWaddr C8:1F:66:D7:3B:FF
inet addr:192.168.2.36 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::ca1f:66ff:fed7:3bff/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
p3p4 Link encap:Ethernet HWaddr 00:0A:F7:3E:CA:8F
inet addr:192.168.3.36 Bcast:192.168.3.255 Mask:255.255.255.0
inet6 addr: fe80::20a:f7ff:fe3e:ca8f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
I have the following corosync.conf
# Please read the corosync.conf.5 manual page
compatibility: whitetank
totem {
version: 2
secauth: off
threads: 0
interface {
ringnumber: 0
bindnetaddr: 192.168.2.0
mcastaddr: 226.94.1.1
mcastport: 5405
ttl: 1
}
interface {
ringnumber: 1
bindnetaddr: 192.168.3.0
mcastaddr: 226.94.1.2
mcastport: 5407
ttl: 1
}
}
logging {
fileline: off
to_stderr: no
to_logfile: yes
to_syslog: yes
logfile: /var/log/cluster/corosync.log
debug: off
timestamp: on
logger_subsys {
subsys: AMF
debug: off
}
}
amf {
mode: disabled
}
I have installed
cluster-glue-libs.1.0.5.x86_64.CentOS
corosynclib.1.4.1.x86_64.CentOS
openais.1.1.1.x86_64.CentOS
cman.3.0.12.1.x86_64.CentOS
pacemaker-libs.1.1.8.x86_64.CentOS
resource-agents.3.9.2.x86_64.CentOS
corosync.1.4.1.x86_64.CentOS
modcluster.0.16.2.x86_64.CentOS
openaislib.1.1.1.x86_64.CentOS
pacemaker-cluster-libs.1.1.8.x86_64.CentOS
pacemaker.1.1.8.x86_64.CentOS
pcs.0.9.26.noarch.CentOS
libqb.0.14.2.x86_64.CentOS
clusterlib.3.0.12.1.x86_64.CentOS
ricci.0.16.2.x86_64.CentOS
pacemaker-cli.1.1.8.x86_64.CentOS
fence-virt.0.2.3.x86_64.CentOS
ccs.0.16.2.x86_64.CentOS
# corosync-cfgtool -s
Printing ring status.
Local node ID 1
RING ID 0
id = 10.15.28.36
status = ring 0 active with no faults
# pcs status corosync
Nodeid Name
1 sv2836.muc.baag
2 sv2837.muc.baag
# crm_mon --one-shot -V
Last updated: Mon Dec 9 14:56:32 2013
Last change: Mon Dec 9 14:07:03 2013 via cibadmin on sv2836
Stack: cman
Current DC: sv2836 - partition with quorum
Version: 1.1.10-1.el6_4.4-368c726
2 Nodes configured
4 Resources configured
Online: [ sv2836 sv2837 ]
ClusterIP (ocf::heartbeat:IPaddr2): Started sv2836
FIXRoute (ocf::baader:FIXRoute): Started sv2836
ipmi-fencing-sv2837 (stonith:fence_ipmilan): Started sv2836
ipmi-fencing-sv2836 (stonith:fence_ipmilan): Started sv2837
Best regards
Andreas Dvorak
_______________________________________________
Pacemaker mailing list: Pacemaker at oss.clusterlabs.org<mailto:Pacemaker at oss.clusterlabs.org>
http://oss.clusterlabs.org/mailman/listinfo/pacemaker
Project Home: http://www.clusterlabs.org
Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
Bugs: http://bugs.clusterlabs.org
--
esta es mi vida e me la vivo hasta que dios quiera
_______________________________________________
Pacemaker mailing list: Pacemaker at oss.clusterlabs.org<mailto:Pacemaker at oss.clusterlabs.org>
http://oss.clusterlabs.org/mailman/listinfo/pacemaker
Project Home: http://www.clusterlabs.org
Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
Bugs: http://bugs.clusterlabs.org
--
esta es mi vida e me la vivo hasta que dios quiera
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.clusterlabs.org/pipermail/pacemaker/attachments/20131209/2758bb68/attachment.htm>
More information about the Pacemaker
mailing list