[ClusterLabs] ClusterLabs.Org Documentation Problem?

[Eric Robinson]

I have a BIG correction.

If you follow the instructions titled, "Pacemaker 1.1 for Corosync 2.x," and NOT the ones entitled, "Pacemaker 1.1 for CMAN or Corosync 1.x," guess what? It installs cman anyway, and you spend a couple of days wondering why none of your changes to corosync.conf seem to be working.

--
Eric Robinson

-----Original Message-----
From: Jan Friesse [mailto:jfriesse at redhat.com] 
Sent: Tuesday, August 22, 2017 11:52 PM
To: Cluster Labs - All topics related to open-source clustering welcomed <users at clusterlabs.org>; kgaillot at redhat.com
Subject: Re: [ClusterLabs] ClusterLabs.Org Documentation Problem?

> Thanks for the reply. Yes, it's a bit confusing. I did end up using the documentation for Corosync 2.X since that seemed newer, but it also assumed CentOS/RHEL7 and systemd-based commands. It also incorporates cman, pcsd, psmisc, and policycoreutils-pythonwhich, which are all new to me. If there is anything I can do to assist with getting the documentation cleaned up, I'd be more than glad to help.

Just a small correction.

Documentation shouldn't incorporate cman. Cman was used with corosync 1.x as a configuration layer and (more important) quorum provider. With Corosync 2.x quorum provider is already in corosync so no need for cman.



>
> --
> Eric Robinson
>
> -----Original Message-----
> From: Ken Gaillot [mailto:kgaillot at redhat.com]
> Sent: Tuesday, August 22, 2017 2:08 PM
> To: Cluster Labs - All topics related to open-source clustering 
> welcomed <users at clusterlabs.org>
> Subject: Re: [ClusterLabs] ClusterLabs.Org Documentation Problem?
>
> On Tue, 2017-08-22 at 19:40 +0000, Eric Robinson wrote:
>> The documentation located here…
>>
>>
>>
>> http://clusterlabs.org/doc/
>>
>>
>>
>> …is confusing because it offers two combinations:
>>
>>
>>
>> Pacemaker 1.0 for Corosync 1.x
>>
>> Pacemaker 1.1 for Corosync 2.x
>>
>>
>>
>> According to the documentation, if you use Corosync 1.x you need 
>> Pacemaker 1.0, but if you use Corosync 2.x then you need Pacemaker 
>> 1.1.
>>
>>
>>
>> However, on my Centos 6.9 system, when I do ‘yum install pacemaker 
>> corosync” I get the following versions:
>>
>>
>>
>> pacemaker-1.1.15-5.el6.x86_64
>>
>> corosync-1.4.7-5.el6.x86_64
>>
>>
>>
>> What’s the correct answer? Does Pacemaker 1.1.15 work with Corosync 
>> 1.4.7? If so, is the documentation at ClusterLabs misleading?
>>
>>
>>
>> --
>> Eric Robinson
>
> The page actually offers a third option ... "Pacemaker 1.1 for CMAN or Corosync 1.x". That's the configuration used by CentOS 6.
>
> However, that's still a bit misleading; the documentation set for "Pacemaker 1.1 for Corosync 2.x" is the only one that is updated, and it's mostly independent of the underlying layer, so you should prefer that set.
>
> I plan to reorganize that page in the coming months, so I'll try to make it clearer.
>
> --
> Ken Gaillot <kgaillot at redhat.com>
>
>
>
>
>
> _______________________________________________
> Users mailing list: Users at clusterlabs.org 
> http://lists.clusterlabs.org/mailman/listinfo/users
>
> Project Home: http://www.clusterlabs.org Getting started: 
> http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
> Bugs: http://bugs.clusterlabs.org
> _______________________________________________
> Users mailing list: Users at clusterlabs.org 
> http://lists.clusterlabs.org/mailman/listinfo/users
>
> Project Home: http://www.clusterlabs.org Getting started: 
> http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
> Bugs: http://bugs.clusterlabs.org
>


_______________________________________________
Users mailing list: Users at clusterlabs.org http://lists.clusterlabs.org/mailman/listinfo/users

Project Home: http://www.clusterlabs.org Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
Bugs: http://bugs.clusterlabs.org