[Pacemaker] corosync/openais fails to start

[Steven Dake]

On 05/27/2010 08:40 AM, Diego Remolina wrote:
> Is there any workaround for this? Perhaps a slightly older version of
> the rpms? If so where do I find those?
>

Corosync 1.2.1 doesn't have this issue apparently.  With corosync 1.2.1, 
please don't use "debug: on" keyword in your config options.  I am not 
sure where Andrew has corosync 1.2.1 rpms available.

The corosync project itself doesn't release rpms.  See our policy on 
this topic:

http://www.corosync.org/doku.php?id=faq:release_binaries

Regards
-steve

> I cannot get the opensuse-ha rpms any more so I am stuck with a
> non-functioning cluster.
>
> Diego
>
> Steven Dake wrote:
>> This is a known issue on some platforms, although the exact cause is
>> unknown. I have tried RHEL 5.5 as well as CentOS 5.5 with clusterrepo
>> rpms and been unable to reproduce. I'll keep looking.
>>
>> Regards
>> -steve
>>
>> On 05/27/2010 06:07 AM, Diego Remolina wrote:
>>> Hi,
>>>
>>> I was running the old rpms from the opensuse repo and wanted to change
>>> over to the latest packages from the clusterlabs repo in my RHEL 5.5
>>> machines.
>>>
>>> Steps I took
>>> 1. Disabled the old repo
>>> 2. Set the nodes to standby (two node drbd cluster) and turned of
>>> openais
>>> 3. Enabled the new repo.
>>> 4. Performed an update with yum -y update which replaced all packages.
>>> 5. The configuration file for ais was renamed openais.conf.rpmsave
>>> 6. I ran corosync-keygen and copied the key to the second machine
>>> 7. I copied the file openais.conf.rpmsave to /etc/corosync/corosync.conf
>>> and modified it by removing the service section and moving that to
>>> /etc/corosync/service.d/pcmk
>>> 8. I copied the configurations to the other machine.
>>> 9. When I try to start either openais or corosync with the init scripts
>>> I get a failure and nothing that can really point me to an error in the
>>> logs.
>>>
>>> Updated packages:
>>> May 26 14:29:32 Updated: cluster-glue-libs-1.0.5-1.el5.x86_64
>>> May 26 14:29:32 Updated: resource-agents-1.0.3-2.el5.x86_64
>>> May 26 14:29:34 Updated: cluster-glue-1.0.5-1.el5.x86_64
>>> May 26 14:29:34 Installed: libibverbs-1.1.3-2.el5.x86_64
>>> May 26 14:29:34 Installed: corosync-1.2.2-1.1.el5.x86_64
>>> May 26 14:29:34 Installed: librdmacm-1.0.10-1.el5.x86_64
>>> May 26 14:29:34 Installed: corosynclib-1.2.2-1.1.el5.x86_64
>>> May 26 14:29:34 Installed: openaislib-1.1.0-2.el5.x86_64
>>> May 26 14:29:34 Updated: openais-1.1.0-2.el5.x86_64
>>> May 26 14:29:34 Installed: libnes-0.9.0-2.el5.x86_64
>>> May 26 14:29:35 Installed: heartbeat-libs-3.0.3-2.el5.x86_64
>>> May 26 14:29:35 Updated: pacemaker-libs-1.0.8-6.1.el5.x86_64
>>> May 26 14:29:36 Updated: heartbeat-3.0.3-2.el5.x86_64
>>> May 26 14:29:36 Updated: pacemaker-1.0.8-6.1.el5.x86_64
>>>
>>> Apparently corosync is sec faulting when run from the command line:
>>>
>>> # /usr/sbin/corosync -f
>>> Segmentation fault
>>>
>>> Any help would be greatly appreciated.
>>>
>>> Diego
>>>
>>>
>>>
>>> _______________________________________________
>>> Pacemaker mailing list: Pacemaker at oss.clusterlabs.org
>>> http://oss.clusterlabs.org/mailman/listinfo/pacemaker
>>>
>>> Project Home: http://www.clusterlabs.org
>>> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
>>