[Pacemaker] primitive dlm ocf:pacemaker:controld --> WARNING: dlm: default-action-timeout 20s for start is smaller than the advised 90

Wed Apr 21 22:28:15 UTC 2010

Thank you Andrew,
I've replaced the incorrect packages installed from SLES HA cd with 
opensuse repository.
Could you please describe the main steps to upgrade pacemaker from 1.02 
to 1.08 and openais 0.8 to corosync 1.2?
I've already a cluster up and running.

The ocfs2-tools should be rebuild because DLM is changed or I can leave 
ocfs2-tools installed from opensuse repository?

Regards,
Roberto.
On 04/19/2010 09:52 AM, Andrew Beekhof wrote:
> On Mon, Apr 12, 2010 at 2:26 PM, Roberto Giordani<r.giordani at libero.it>  wrote:
>    
>> Hi Andrew,
>> these are the rpms installed on Opensuse 11.2 x86_64 to obtain a cluster
>> with OCFS2 and DLM support on Xen kernel
>>
>> pacemaker-pygui-1.4-15.1.x86_64
>> pacemaker-1.0.8-4.x86_64
>> libpacemaker3-1.0.8-4.x86_64
>>
>> libdlm-2.99.08-10.4.x86_64
>> libdlm2-2.99.08-10.4.x86_64
>>
>> corosync-1.2.1-1.x86_64
>> libcorosync-1.2.1-1.x86_64
>>
>> heartbeat-3.0.2-2.x86_64
>> heartbeat-common-2.99.3-14.3.x86_64
>> heartbeat-resources-2.99.3-14.3.x86_64
>>
>> libglue2-1.0.3-1.x86_64
>> libgssglue1-0.1-8.2.x86_64
>> cluster-glue-1.0.3-1.x86_64
>>
>> resource-agents-0.9-2.1.x86_64
>>
>> ocfs2-tools-o2cb-1.4.1-25.6.x86_64
>> ocfs2console-1.4.1-25.6.x86_64
>> ocfs2-tools-1.4.1-25.6.x86_64
>>
>> libopenais2-0.80.3-26.2.x86_64
>>
>> Attached there are:
>> -) corosync.conf
>> -) corosync log
>> -) /var/log/messages
>>
>> -) xml configuration
>>
>> I've observed that opensuse 11.2 doesn't have heartbeat-common,
>> heartbeat-resources,
>>      
> heartbeat-common has been replaced by libglue2 and heartbeat-resources
> by resource-agents.
> you definitely shouldn't have both sets of packages installed.
>
>    
>> libdlm, libdlm2 updated to 3.0.2-2,
>>      
> where did you get these from?
>
>    
>> and if I try to install libopenais2-1.1.0-1.x86_64.rpm from clusterlabs, I
>> should remove ocfs2-tools, libdlm and pacemaker-pygui.
>>      
> right because they were built for (and therefor require) an older
> version than the ones on clusterlabs.org
> no wonder the dlm and ocfs2 aren't starting.
>
> either:
> a) only use what comes in 11.2
> b) install everything from clusterlabs.org and rebuild the gui, dlm
> and ocfs2-tools packages
>
>    
>> So this semas the only way to have ocfs2 and dlm support on Opensuse 11.2
>> Any idea to run a pacemaker cluster with this scenario?
>> Thank you for your investigation :-)
>>
>> On 04/12/2010 09:10 AM, Andrew Beekhof wrote:
>>
>> Hi,
>>
>> Please provide (as compressed attachments): logs and the pacemaker
>> configuration
>> This is the minimum we require in order to comment intelligently on
>> your question.
>>
>> -- Andrew
>>
>>
>> On Sun, Apr 11, 2010 at 6:32 PM, Roberto Giordani<r.giordani at libero.it>
>> wrote:
>>
>>
>> Hello,
>> I've started a new cluster with 4 nodes that should work with ocfs2
>> When I try to configure the dlm primitive I've received the following
>> warning and the the dlm-clone doesn't  start.
>>
>> crm(live)# cib new stack-glue
>> INFO: stack-glue shadow CIB created
>> crm(stack-glue)# configure primitive dlm ocf:pacemaker:controld op monitor
>> interval=120s
>> WARNING: dlm: default-action-timeout 20s for start is smaller than the
>> advised 90
>> WARNING: dlm: default-action-timeout 20s for stop is smaller than the
>> advised 100
>> WARNING: dlm: default-action-timeout 20s for start is smaller than the
>> advised 90
>> WARNING: dlm: default-action-timeout 20s for stop is smaller than the
>> advised 100
>> crm(stack-glue)# configure clone dlm-clone dlm meta interleave=true
>> WARNING: dlm: default-action-timeout 20s for start is smaller than the
>> advised 90
>> WARNING: dlm: default-action-timeout 20s for stop is smaller than the
>> advised 100
>> crm(stack-glue)# cib commit stack-glue
>> INFO: commited 'stack-glue' shadow CIB to the cluster
>> crm(stack-glue)# quit
>> bye
>>
>> This is the crm_mon status
>> ============
>> Last updated: Sun Apr 11 18:30:42 2010
>> Stack: openais
>> Current DC: node4 - partition with quorum
>> Version: 1.0.8-9881a7350d6182bae9e8e557cf20a3cc5dac3ee7
>> 4 Nodes configured, 4 expected votes
>> 1 Resources configured.
>> ============
>>
>> Online: [ node1 node2 node3 node4 ]
>>
>>
>> Failed actions:
>>     dlm:0_start_0 (node=node2, call=5, rc=7, status=complete): not running
>>     dlm:2_start_0 (node=node3, call=3, rc=7, status=complete): not running
>>     dlm:0_start_0 (node=node1, call=3, rc=7, status=complete): not running
>>     dlm:3_start_0 (node=node4, call=3, rc=7, status=complete): not running
>>
>>
>> Any idea?
>>
>> Regards,
>> Roberto.
>>
>> _______________________________________________
>> Pacemaker mailing list
>> Pacemaker at oss.clusterlabs.org
>> http://oss.clusterlabs.org/mailman/listinfo/pacemaker
>>
>>
>>
>> _______________________________________________
>> Pacemaker mailing list
>> Pacemaker at oss.clusterlabs.org
>> http://oss.clusterlabs.org/mailman/listinfo/pacemaker
>>
>>
>> _______________________________________________
>> Pacemaker mailing list: Pacemaker at oss.clusterlabs.org
>> http://oss.clusterlabs.org/mailman/listinfo/pacemaker
>>
>> Project Home: http://www.clusterlabs.org
>> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
>>
>>      
> _______________________________________________
> Pacemaker mailing list: Pacemaker at oss.clusterlabs.org
> http://oss.clusterlabs.org/mailman/listinfo/pacemaker
>
> Project Home: http://www.clusterlabs.org
> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
>    